Menu
Select any topic from the menu below. Click on a question to open and/or close the answer.
We recommend saving as a PDF file. You may also send the file in the following types: JPG, JPEG, TIF, TIFF, and EPS.
We prefer that you send PDF with embedded or outlined fonts. PDF files are easier to handle and will likely speed up your turn-around. Remember to flatten your files before uploading.
For Roll Labels, we recommend designing:
Your designs should always start and finish in CMYK color mode.
These colors are in RGB
These are the same colors but in CMYK
If you send us an RGB file, there is a chance that a color shift may occur and you may not be satisfied with your job.
Your artwork files should be at 300 dpi.
These are 72 dpi low res images
These are the same images but at 300 dpi
Low-resolution files may be printed as is or will be placed on hold until we receive new files, slowing your turn-around.
Bleed must extend past the cut-line and will be trimmed from the product during the final cutting phase. When the image is required to extend all the way to the edge, bleed is needed to preserve the finished look and the quality of the final product.
Please keep all text at least 0.125″ inside the cut-line.
We recommend using our templates at all times.
Yes, but if the border is too close to the cutline, it may be cut off-center slightly.
We cut through many sheets at a time, so watch your borders to avoid an unwanted mistake.
Any transparency issue can be resolved before saving your file.
What a transparency problem looks like on screen… After a transparency problem is printed…
To prevent this, never use shadows, glows, or any other transparency (image or otherwise) on top of a spot color. Always convert your spot color to CMYK and flatten before sending.
SHADOWS, GLOWS, TRANSPARENCY
All of these effects will cause transparency problems.
When sending artwork, do not send extra files, like proofs or samples, because they might get printed. Only send the files you need printed.
DO NOT SEND THESE KINDS OF FILES
We are not responsible for these kinds of files being printed. Unless requested by one of our employees, DO NOT send files that you do not want printed.
Primarily used to intentionally overlap inks for a number of reasons, overprint can cause unexpected results. We suggest that you turn all overprint objects off before submitting your files.
ON SCREEN VIEWAFTER PRINTING
In this case the logo was set to overprint. The colors from logo are mixing with the colors from the background. Unexpected results may occur if you have accidentally set certain objects to overprint. Always check logos and other artwork before submitting.
We only except seperate files for each side of your job. Please note, if you send us both sides on the same artwork your job will not print correctly.
2 FILES – 1FR, 1BK / 1 FILE – FR&,BK
We can only use one type of foil per order, for example, you can not order a Foil Worx job with Gold foil on the front and Silver foil on the back. Foil job files are set up just like our Spot UV job files. You must provide a separate Foil mask file: black in the areas you want the foil and white in the areas you do not want the foil. All black areas should be solid 100% K with no other added colors. If you order a Foil Worx job with Spot UV, you’ll need to provide separate mask files for the Foil (foil mask) and UV (spot uv mask) , in which case you may be required to provide up to 6 files. Please keep in mind, however, that the Foil and UV coating can’t overlap, both should be at least 1/16″ apart to avoid foil peeling off. Also, avoid using small / fine text or lines for foil objects. For best results, please make sure that foil coverage is less than 50% of the entire print side. Also, be aware that there may be up to a 1/16″ shift on the placement of the foil. Keep this in mind if you are trying to align foil with other printed artwork on the card.
For better quality we recommend creating mask files in vector based programs such as Illustrator or CorelDRAW.
With Akuafoil, you can turn a wide range of CMYK colors into multi-colored foils. Akuafoil uses a special processed foil system that is applied under a 4/c process to create an array of foil colors. It’s simple, affordable, and makes your prints stand out from the crowd.
For an Akuafoil job, you must include an Akuafoil mask file along with your CMYK file. The mask file indicates where the Akuafoil will be applied. The file setup is the same as Spot UV. Use 100% K where Akuafoil needs to be applied and white where the Akuafoil is not applied.
As shown above, the file on the left is the normal CMYK print file. If you want the logo to be Akuafoil, then your Akuafoil mask file should look like the file on the right. The white indicates no Akuafoil and black 100% K indicates where the Akuafoil will be applied. When uploading, please remember to upload separate files.
Here are some more things to keep in mind when creating your Akuafoil artwork:
Make sure the mask and CMYK print file are aligned. They should match exactly in size and position.
–Akuafoil works best on lighter colors. The darker the CMYK color, the less vibrant the Akuafoil effect.
–Do not use very thin or small text and artwork with Akuafoil. Use San Serif fonts above 12 point for best results.
–If you have Akuafoil applied to a white area, it will have a plain silver Akuafoil look.
–For better quality we recommend creating mask files in vector based programs such as Illustrator or CorelDRAW.
If you would like plain silver Akuafoil to print, make sure to have at least 15% K in the CMYK print file area in order to obtain the highest quality silver Akuafoil effect.
When creating knockouts in the Akuafoil mask or in the CMYK print file, please be aware that there might be a “Halo” of white around the knockout area. Below are two examples: On the left, a file with a CMYK magenta background and a knockout for the Akuafoil text. On the right, an Akuafoil background with a knockout for the CMYK text.
These are the printed results:
You can see the white “Halo” in-between the CMYK ink and the Akuafoil. To prevent this, grow/stroke the Akuafoil area in the mask by 1 point. This will allow the Akuafoil to bleed into the CMYK area, reducing the white “Halo” effect. You can also fill in the knockout with a color to reduce the effect further.
Our 14pt Metallic Pearl paper is a unique stock that shimmers in light when viewed from different angles. The stock itself is embedded with Pearl fibers that give the paper an overall smooth, metallic look. Printing on this stock will give your CMYK colors a subtle shimmer, however heavy ink densities or coverage may diminish the effect.
Our 14pt Metallic Pearl paper is a unique stock that shimmers in light when viewed from different angles. The stock itself is embedded with Pearl fibers that give the paper an overall smooth, metallic look. Printing on this stock will give your CMYK colors a subtle shimmer, however heavy ink densities or coverage may diminish the effect.
Our 14pt Natural Cards are a light cream, natural white color with a smooth finish. The stock has a minimum of 30% post-consumer waste content. Samples are available in our 4over Trade Printing Sample kit.
Luster cards are printed on 16pt card stock and have a 3mil gloss lamination making them 22pt thick.
We start with 16pt stock as a base and apply 1.5mil soft velvet, scuff resistant laminate to both sides of the sheet for a total thickness of 19pt. The soft velvet lamination adds a soft supple look and feel, which softens colors, reduces contrast and gives an overall lighter, muted appearance.
Suede Cards are water resistant, but not waterproof. This means the cards stand up well when they come in contact with a small amount of water, but cannot be submerged in water without water seeping into the card and causing damage. Please test your specific application to ensure the cards are appropriate for that use.
The term “Suede” refers to the soft, supple texture of the cards, not the actual materials used. A soft velvet laminate is applied to both sides of the card to achieve a luxurious suede-like look and feel.
Spot UV is a flat finish of a shiny layer that goes on the exact spot where you would like your printed piece to have an area of a high gloss coating.
Raised Spot UV is the same process, except the UV that gets applied stands out from the product, that if you run your fingers over the card you will feel the UV. The depth of the Raised Spot UV is 50 microns.
It is recommended that you do not use smaller than 6pt font on the Raised Spot UV Artwork. If, however, you use fonts with thicker strokes, it is recommended that you do not use smaller than 9pt font.
For best results, please make sure that UV coverage is less than 30%. Otherwise, the cards will be stuck together and become a block of cards. Also, The mask file must be a vector art created in a vector-based program such as Illustrator. Otherwise, you won’t have sharp edges on the artwork.
Up to 70% coverage is acceptable only with patterns, thin strokes or small shapes. Ideally, the size of the area, shape or image covered with raised foil should not exceed 1in x 1in.
Please see the pictures below for reference.
When designing plastic cards, it is important to keep in mind that the frosted and clear plastic cards are transparent. Also, all plastic cards come with round corners at no extra charge.
As you can see, the difference in the transparency is shown in the image above. The clear cards (right) are completely transparent. The frosted cards (center) are semi-transparent and cannot be seen through easily. The opaque white plastic cards (left) are solid white and not transparent at all. Keep this in mind when designing your plastic cards, it will affect how your design will print.
–Printing on Clear and Frosted Plastic Cards will come out slightly lighter than average compared to other stocks. This is due to the plastic itself and is not a production issue.
–When setting up a rich black value, please make sure to use C 60 M 40 Y 40 K 100 . Do not use all 100 since it will cause problems and will not print any darker on plastic.
Since there is no white ink in CMYK, it is important to keep in mind that the frosted and clear plastic cards are transparent. The three designs above are the same as in the first picture. You will notice that the white area in the clear cards (right) and the frosted cards (center) has no ink and will show the transparent material it’s printed on. In this case, the clear cards and frosted cards white area show up with no ink on the printed piece. Also, keep in mind that all colors that are printed on clear cards or frosted cards will be transparent as well.
With the clear plastic cards, there might be a small percentage that may have light scratches. This issue originates from the manufacturer and is due to the material and handling. To help compensate for this, we run overs of the clear plastic cards to help meet the required quantity.
Clear plastic cards will come with a thin protective layer on one side that can be peeled off. This is to prevent the cards from scratching during packaging and shipping.
Booklets are a little more complex to design. Also, if you have artwork you created from another company, it might not meet 4over rules. For best results, please download our templates available here.
Here are rules to follow when creating your Booklets:
• Page counts start on the cover as page 1, inside cover as page 2 and so on.
• Total bleed is .25” and total Safety is .5”. For example, an 8.5×11 booklet with bleed should be 8.75×11.25 total. This allows us to set up your crossovers properly.
• Only single pages will be accepted. NO readers OR printers spreads.
• We prefer a multipage PDF but single page files are also ok.
Our page counts for booklets start on the cover as page 1, inside cover as page 2 and so on. In the example below, you will see a 8pg booklet. Each page will show the page number. Click and hold the page corners to turn the page. This is also reflected in our templates.
Crossovers are common in booklets and require extra attention. A Crossover is an image, text or other graphic element that goes from one page to another.
Below you can see a good example of how to create crossovers:
Designers must pay close attention to the crossover design and make sure it is as seamless as possible on the finished piece. Also, do not use text or thin lines as crossovers. Big pictures work best.
Note: Due to the nature of saddle stitch binding, crossovers may not line up 100% on the final booklet.
Artwork done in Indesign or other layout software as spreads or facing pages must be saved out as single page pdfs. When creating your design, keep this in mind especially when doing crossovers. The easiest way is to create the bleed is when creating your document. Below are instructions on how to create your document in Indesign.
When creating your document, make your page size the cut size and your margin size .25” for safety for a .5” total:
Then, click the More Options button on the right. It will reveal Bleed and Slug settings below. Enter .125” as the bleed for a total of .25”:
Your Indesign document is now ready for proper booklet layout. You should see proper bleed and safety guidelines:
When your ready to export your booklet as PDF, make sure to Use Document Bleed Settings in the Marks and Bleeds menu:
After submitting your booklet, you will receive an email from our online booklet proofing system called Fourte. This system will allow you to double check all the pages and make sure they are in the correct order. There you can approve or decline and re-upload pages if you need to. You will also be able to preview your booklet as if it was printed and bound.
Perfect Binding gives your booklets a more finished, refined look. With this binding method, the pages and cover are glued together at the spine with a strong, yet flexible, thermal glue.
Templates are available for both the cover and inside pages of the Perfect Bound Booklets. Download templates here.
Please note: Unlike our regular Booklets, the page count specified in the product name does not include the cover. E.g. “8.5 x 11, 52-Pages” will require you to upload 48 inside pages + 4-page cover file (which is always 4:0) .
We recommend you do not specifically design on the spine. Backgrounds or images that wrap around the book are preferred. Creating designs with text, borders or colors that are centered only on the spine may cause it to look uneven during the binding process.
Templates are available for the covers of the Perfect Bound Catalogs and relate to the number of inside pages. The normal 8.5×11 and 8.5×5.5 flat, Flyer templates can be used for all the inside pages. Download templates here.
Currently we do not offer samples for Perfect Bound Catalogs.
Currently we do not offer samples for Perfect Bound Catalogs.
* 1/16” overbleed and color wrap onto the back of the envelope is required to allow for movement throughout the bindery process.
* Artwork with bleed on face or print on any flaps must be placed on 4over certified envelope templates.
*Solid, full color envelopes are recommended (to eliminate overbleed) .
* Intentional extension of flap color onto envelope face is recommended.
* Gradients are recommended for smoother color transitions.
* Click Here to view important envelope artwork guidelines.
* The bleed required is 0.125″ (0.0625″ on each side) .
* Text and images should be at least 0.25″ from the edge.
* Artwork with more than 40% ink coverage must be submitted as an offset product.
* Full color backgrounds should be avoided.
* Use a white backgrounds with low ink coverage (e.g. logo and text only) .
* Avoid or limit use of transparencies and gradients.
* For window envelopes, the window area must be free of ink.
* For Digital Envelopes:
4/0 = Full Color Front
4/4 = Full Color Front and Full Color on Back Flaps
0/4 = Full Color on Back flaps
Yes. To get print on the back flaps only, choose 0/4. For print on the front and the back flaps, choose 4/4. Keep in mind, artwork with more than 40% ink coverage must be submitted as an offset product.
4/0 = Full Color Front
4/4 = Full Color Front and Full Color on Back Flaps
0/4 = Full Color on Back flaps
Follow 4over certified templates for correct window placement.
DO NOT place artwork or color on the window area. Keep images at least 1/8″ inch away from the edge of the window. Digital Envelopes are pre-converted and have a plastic window adhered to the window area prior to printing. The window area must be blank.
Yes. Landscape booklets are available by choosing Short Edge Binding from the drop-down menu Binding Edge.
We recommend saving as a PDF file. You may also send the file in the following types: JPG, JPEG, TIF, TIFF, and EPS.
We prefer that you send PDF with embedded or outlined fonts. PDF files are easier to handle and will likely speed up your turn-around. Remember to flatten your files before uploading.
For Roll Labels, we recommend designing:
Your designs should always start and finish in CMYK color mode.
These colors are in RGB
These are the same colors but in CMYK
If you send us an RGB file, there is a chance that a color shift may occur and you may not be satisfied with your job.
Your artwork files should be at 300 dpi.
These are 72 dpi low res images
These are the same images but at 300 dpi
Low-resolution files may be printed as is or will be placed on hold until we receive new files, slowing your turn-around.
Bleed must extend past the cut-line and will be trimmed from the product during the final cutting phase. When the image is required to extend all the way to the edge, bleed is needed to preserve the finished look and the quality of the final product.
Please keep all text at least 0.125″ inside the cut-line.
We recommend using our templates at all times.
Yes, but if the border is too close to the cutline, it may be cut off-center slightly.
We cut through many sheets at a time, so watch your borders to avoid an unwanted mistake.
Paper Board Boxes are available on durable 14PT Uncoated with No Coating and on 18PT C1S stock with coating options of No Coating, UV Coating, Front Only or Spot UV, Front Only *.
* UV Coating, Front Only is not available for boxes that have glue, including the Wine Box and Sales Presentation Box.
– Cube Boxes and Golf Ball Boxes have sturdy edge-lock tabs for the side and snap lock bottoms to keep them held together securely without glue.
– Pillow Boxes are available with edge-lock tabs for all quantities. Side glue is an available option for quantities of 250 or more.
– Roll End Tuck Top Boxes and Business Card Boxes are self tuck and don’t require glue or tape for assembly.
– Sales Presentation Boxes come glued on one side with a tuck and tongue closure on the bottom. Each box comes with velcro dot closure for the top flap. Velcro dot will be included in the package, assembly is required.
– Wine Bottle Boxes are glued on one side and have a snap lock bottom which securely holds the weight of a bottle of wine.
– Custom Boxes include options to add Glue Straight Line or Glue Auto Lock Bottom.
Our 14pt Metallic Pearl paper is a unique stock that shimmers in light when viewed from different angles. The stock itself is embedded with Pearl fibers that give the paper an overall smooth, metallic look. Printing on this stock will give your CMYK colors a subtle shimmer, however heavy ink densities or coverage may diminish the effect.
Our 14pt Metallic Pearl paper is a unique stock that shimmers in light when viewed from different angles. The stock itself is embedded with Pearl fibers that give the paper an overall smooth, metallic look. Printing on this stock will give your CMYK colors a subtle shimmer, however heavy ink densities or coverage may diminish the effect.
Our 14pt Natural Cards are a light cream, natural white color with a smooth finish. The stock has a minimum of 30% post-consumer waste content. Samples are available in our 4over Trade Printing Sample kit.
1. What are the specifications of the available Roll Label stocks?
2. What is the core size and outer diameter?
3. What shapes are offered?
4. Are custom shapes available? How do I set them up and what bleed is required?
5. Will my dispenser work with your Roll Labels?
6. Will the print quality of my Roll Label be comparable to that of Offset?
7. What does the Unwind Direction refer to?
8. How do I set up my Roll Label file and what are the bleed requirements?
9. How do I set up and create a Bright Metallic Silver or Clear Roll Label with white ink?
10. Are Roll Labels safe for Food Packaging?
11. Why do square and rectangle Roll Labels have rounded corners?
12. Are your Roll Lables recommended for both Indoor and Outdoor use?
13. Will a mask file be required?
14. How do I set up my file to avoid registration issues?
15. What’s the minimum font size recommended for use on Bright Metallic Roll Labels?
16. What lamination options are available for Roll Labels?
17. What are the benefits of lamination for Roll Labels?
18. Can Roll Labels be written on?
19. How should I design my artwork using black font?
20. How should I design Barcodes and QR codes using black font?
21. How do I design vector files?
Bright Silver Metallic – 2mil
Bright Silver Metallic comes standard in a 2mil thickness. Offering excellent tear strength and opacity, these mirror-like labels are heat and chemical resistant and are suitable for application on a variety of surfaces. We recommend them for indoor use. We offer white ink as a 5th color. Please see FAQ #9 below for details on how to set up your artwork with white ink prior to uploading.
Clear BOPP – 2.3mil
Clear BOPP is made of Glossy Clear Biaxially Oriented Polypropylene with a permanent adhesive that sticks well to a variety of surfaces. BOPP is oil and water resistant but we only recommended it for indoor use. We offer white ink as a 5th color. Please see FAQ #9 below for details on how to set up your artwork with white ink prior to uploading.
Eggshell Felt – 70lb, 6.3mil
70lb Eggshell Felt features a distinct texture, high opacity and excellent ink holdout. This facestock also contains 30% post consumer waste content making it an excellent choice for eco-friendly applications. It is manufactured with wet strength properties to increase performance in moist environments. These are not recommended for outdoor use. We recommend that you test your specific application.
Semi-Gloss Paper – 55lb, 3.2mil
Semi-Gloss Paper is a budget friendly solution that doesn’t sacrifice quality for economy. Semi-Gloss Paper stock has a permanent adhesive that sticks well to a variety of surfaces. It is not resistant to oil or water and is recommended for indoor use only.
White BOPP – 2.3mil
White BOPP is made of Glossy White Biaxially Oriented Polypropylene with a permanent adhesive that sticks well to a variety of surfaces. White BOPP is oil and water resistant but we only recommended it for indoor use.
All of our Roll Labels have a 3″ core and an outer diameter of up to 6″.
Our Roll Labels are available in the following standard shapes: Oval, Circle, Square (with Round Corners) and Rectangle (with Round Corners) . Custom Shapes are also available for the following sizes: 1″ x 1″, 2″ x 2″, 3″ x 3″, 4″ x 4″, 5″ x 5″ and 6″ x 6″.
Yes, Custom Shaped Roll Labels are available for the following sizes: 1″ x 1″, 2″ x 2″, 3″ x 3″, 4″ x 4″, 5″ x 5″ and 6″ x 6″. Choose from the size that best fits your needs, then select the Shape Option: Custom Roll Label. On the upload page you will be asked to upload the Front Artwork file and the Custom Shape File.
Custom Roll Label File Guidelines:
Custom shape file must be created a vector and saved as an EPS or PDF
Custom shape file should represent the cut line
Custom shape file should be a black line, 0.5pt to 1pt thick
Thin lines and small shapes are not recommended
Shapes smaller than 1/8″ may have unexpected results and are not recommended
Bleed for Roll Labels is 0.125″ from the cut line on all sides
Example of Custom Roll Label:
Acrylic boasts a variety of high-performance properties, among the most important being its optical clarity, low UV sensitivity, and overall weather resistance. Acrylic offers clear, glass-like brilliance and translucence, but is much lighter and much more durable than glass. Acrylic is easy to form, with high impact resistance, excellent transparency, and superior weather-ability.
Thickness: 1/4
Bleed: ensure you have .5″ on all sides of your artwork, do not add crops.
Turn great composition into greater sales with high quality Aluminum Dye Sub Panels. Printed on 0.045″ white gloss panels using dye-sublimation, these aluminum metal prints enhance photo vibrancy for an eye-catching impact. Aluminum Dye Sub Panels are available in a variety of sizes with an optional stand-off accessory sold separately.
Thickness: 3mm (1/8″)
Bleed: ensure you have .5″ on all sides of your artwork, do not add crops.
Aluminum Floor Graphic is a rugged 20mil aluminum foil material and is designed to naturally conform to the texture of rough or smooth surfaces. The high-friction / slip-resistant surface improves the stability of pedestrian traffic in the area it is applied to. It’s designed to withstand harsh weather conditions in both hot and cold weather conditions. It is Printed directly on the material using UV cured inks and the material is rated for outdoor use, this material would last long outdoors. Harsh conditions and /or extreme traffic may wear down the slip resistance and require the graphics to the replaced earlier for safety precautions. Indoor applications and locations with lighter pedestrian traffic can exceed life expectancy. This material surpasses anti-slip safety standards, both when wet or dry.
Bleed: ensure you have 0.5″ on all sides of your artwork, do not add crops.
Aluminum Heavy Duty is printed on a sturdy, rust-proof 0.08″ aluminum for maximum outdoor durability. Available in a variety of sizes with round corners, straight corners or contour cutting. Meet any mounting requirements with optional 3/8″ drill holes or standoff hardware—available in a range of placement positions for greater versatility. Most commonly used outdoors, although functional indoors as well. Common uses include: parking signs, traffic signs, factory and warehouse notifications, directional signage and more.
Thickness: .080
Bleed: ensure you have .5″ on all sides of your artwork, do not add crops.
Aluminum Sandwich Boards are printed with UV inks and comprised of two .012″ aluminum sheets with a polyethylene core, resulting in a total thickness of 1/8″(3mm). They are lightweight and come in two pre-painted colors: White &,amp, Brushed Silver. Drill hole options are available for quick and easy attachment to posts, fences, walls and a variety of surfaces. Aluminum Sandwich Boards are suitable for both indoor and outdoor use. Common uses include: real estate signage, customer/handicap notices, directional signs and much more.
Thickness: 3mm (1/8″)
Bleed: ensure you have .5″ on all sides of your artwork, do not add crops.
EDDM is a U.S. Postal Service program developed to help businesses get their promotions and advertisements into the hands of a targeted audience, while reducing the cost of preparing and delivering mailing campaigns.
It’s the perfect solution for businesses large and small, allowing you to target homes in your area or across the country. No mailing list or postage permit is required, which saves you time and money. We have a Print Only option, where we print the pieces and you handle the rest of the process with USPS and a Full Service solution, where we take care of everything. With Full Service, postage is as low as 0.197¢ per piece, saving you a bundle over first class rates!
Please note: EDDM orders must meet “commercial flat” specifications and all other USPS requirements. Our built in EDDM Full Service tool and our EDDM Full Service templates make these specifications easy to adhere to.
EDDM Print Only includes sizes and options which are USPS approved for EDDM processing. We print and ship to you just like a normal postcard. Be aware that artwork must include an approved USPS EDDM indicia, return address and must be designed within USPS EDDM specifications. Please visit the USPS website at https://www.usps.com/business/every-door-direct-mail.htm for more information.
EDDM Full Service takes all the guess work out of the EDDM process. Choose your print product, then select your routes using our simple and easy online route selection map, then upload your artwork. We take care of the printing, bundling, EDDM processing, paperwork and delivery to USPS. The USPS postage fee is included in the final price at checkout.
It is required that the artwork have our indicia on one side, so be sure to use our EDDM Full Service templates before uploading your artwork.
For the Print Only option, make sure to download and use our EDDM Print Only templates and follow all standard USPS EDDM requirements. For more information, please visit: https://www.usps.com/business/every-door-direct-mail.htm
For the Full Service option, where we take care of the processing and delivery to USPS, make sure to download and use our EDDM Full Service templates. The templates include our indicia and guide for were to position the return address.
Indicia and Return Address Positioning:
our indicia and a return address must be on the artwork.
the indicia and return address must be on one side of the print piece.
the indicia and return address must be positioned in the top half of the artwork.
for 4/0 artwork, the indicia and address must be placed on the front.
Below is a sample of our full service template for the proper lay out of your artwork:
PDF files are recommended. We accept the following file types: pdf, jpg.
We offer two different size Mugs, 11oz and 15oz. Our Mugs are made from a high quality ceramic and are microwave and dishwasher safe.
Our Traditional Locking-Pin Buttons are printed at near photo quality and have a durable metal locking-pin backer.
Available Sizes:
Round – 1×1, 1.25×1.25, 2.25×2.25, 3×3, 3.5×3.5
Rectangle – 2.5×3.5, 2×3
Square – 2×2
Diamond – 2×2
Our Magnet Buttons are printed at near photo quality and have a magnetic backer.
Tote Bags are made of a sturdy, 100% cotton that is eco-friendly and useful for anything from grocery shopping to hitting the gym. The 6oz cotton canvas material is washable and reusable. Dual self-fabric straps offer convenient over-the-shoulder carry, leaving hands free for shopping applications.
Tote Bags are available in Natural (off-white), Blue (royal), and Red colors.
We offer various types of T-Shirts, made from 100% cotton. Our current selection of colors include: White, Black, Red, Blue and Gray. Adult sizes range from S to XXL. Kids sizes range from XS to XL. (NOTE: Ladies Short and Long Sleeve T-Shirts are Slim Fit)
No. Our selected carriers do not generally ship to PO Box addresses. Economy shipping, if available, will ship to a P.O.Box.
You cannot ship one order to two different places. For example, Job ID J55555-001 and J55555-002 will get a shipping address each but job number B55555-001 cannot ship to two different places.
Yes. We can drop ship a package to your customer. Simply select the option Drop Ship then select an address from your Address Book. The order will now ship with your billing address or you can update the ship from address by clicking on edit and it will be shipped to the address chosen from your address book.
We do not provide a pricing or weight list but you may get immediate shipping pricing on our website when placing an order.
We offer Common Carrier shipping with multiple service methods e.g. Ground, Next Day Air, etc.
Purolator shipping service is available to US and Canadian residents only for orders produced and shipped within Canada.
Click Here ,to register for an account. You can also find a link on the homepage. There will be a button at the top right. Click the “Apply for a new account” button to register for a new account.
Yes, Click Here ,to visit our General FAQ to view file prep help.
Yes, Click here to visit our Template page to find all our different templates. You can also download them from the various product pages where you’ll find specific templates.
After logging in, your Dashboard will show all your most recent orders. You can also view your full order history by clicking on “My Orders” under the “Order Information” section of the Dashboard. You can reach the Dashboard by clicking on “My Account” at the top of the page.
Yes! You can either save them in your Dashboard by clicking on “Address Book” under the “Your Account” section. You can also save addresses during an order. Click “Add Address” within the shipping section.
